Buy wood briquettes for a tiled stove
Our wood briquettes consist of pressed, natural wood chips. They are suitable for tiled stoves, fireplaces and kitchen stoves, provided the operating instructions for your stove allow wood briquettes. We deliver them in large quantities, on pallets or by truck, to Germany, Austria and Switzerland. You choose between RUF, Nestro and Pini Kay. You can clarify quantities, delivery times and prices using our contact form or directly in the Shop.
Wood briquettes for tiled stoves: types, quantity and purchase at a glance
Wood briquettes for tiled stoves are pressed chips made from natural wood and are approved solid fuels. They burn quietly, leave little ash and take up less storage space than logs. One point remains with the stove: the permitted amount of fuel per burn is stated in your operating instructions, not on the briquette packaging. We deliver wood briquettes in tons and truckloads and show here what you should check before ordering.
Key takeaways
- Wood briquettes made from natural wood are permitted according to the 1st BImSchV.
- The calorific value is around 5 kWh per kilogram.
- The amount of fuel per burn is determined by the stove manufacturer.
- Bark briquettes are not permitted in fireplaces; the instructions for your tiled stove will decide.
- Store in a dry place to preserve the quality.
Can you burn wood briquettes in a tiled stove?
The 1st BImSchV allows wood briquettes made from natural wood according to DIN 51731 or equivalent quality, provided the moisture content is below 25 percent.
The requirement is in § 3 of the 1st BImSchV. The German Environment Agency expressly includes presses made from natural wood in the list of permitted fuels. The Bavarian State Office for the Environment specifies wood briquettes according to DIN 51731 or EN 14961 Part 3 for fireplace stoves. The same source excludes waste wood and bark briquettes for stoves. I cannot confirm whether this also applies to your tiled stove. Check the nameplate and instructions.
The regulation applies in Germany. We have not evaluated any regulations for Austria and Switzerland. Ask your chimney sweep or chimney sweep there.

What calorific value do wood briquettes have compared to logs?
Wood briquettes deliver around 5 kWh per kilogram and, due to the low residual moisture, usually have a higher calorific value than air-dry logs.
haustechnikdialog.de puts this at around 5.0 kWh per kilogram. When it comes to logs, the more water there is in the wood, the lower the calorific value. The LANUV NRW recommends a maximum of 18 percent wood moisture for low-emission operation. A manufacturer data sheet claims that 1,000 kg of wood briquettes replace the calorific value of around 3 cubic meters of mixed wood. This is a manufacturer’s information and not a neutral measurement. You can find a detailed comparison in our calorific value comparison and wood briquettes or firewood.
| Fuel | Legal framework | Humidity | Suitable for the tiled stove | Note |
|---|---|---|---|---|
| Wooden briquettes made from natural wood | permissible according to 1. BImSchV | below 25 percent | suitable for all types of briquettes | around 5 kWh/kg |
| Logs | permissible, natural | less than 25 percent, ideally a maximum of 18 percent | Beech, ash, oak are considered suitable. | Heat value depends on the type of wood and moisture |
| Bark briquettes | not permitted in fireplace stoves according to the LfU Bavaria | According to manufacturer’s information | Instructions decide | for tiled stoves not finally clarified |
| Lignite briquettes | permitted according to 1. BImSchV | not relevant | keep the ember bed for hours | Not a wood product |
The suitability for tiled stoves is based on sanier.de, the types of wood on Raiffeisen Vorarlberg. If you are weighing up wood and coal, read our article “Wood briquettes or coal briquettes”.
How many wood briquettes are you allowed to use per burn?
Only use the amount that the oven manufacturer specifies in the operating instructions for one burn. Too much fuel can overheat the oven.
A tiled stove works in individual burns and stores the heat in the storage mass. The operating instructions for a Brunner tiled stove get to the point:
“The permitted amount of fuel must be applied.”
A discussion in the Fachforum bau.de mentions cracks in the fireclay as a possible consequence of permanent overheating. This is a forum summary and not a test report. If in doubt, ask the manufacturer or your chimney sweep.
How do you light wood briquettes in a tiled stove?
- Ignite with dry kindling material and a small amount of logs, as your instructions indicate.
- Wait until a bed of embers has formed. The HKI describes for wood burning that only then larger logs or wood briquettes are placed.
- Place the permitted amount of wood briquettes and regulate the air according to the manufacturer’s instructions.
- Refill: For tiled stoves, according to State of Upper Austria, only after 8 to 10 hours.

Which type is best for your tiled stove?
All types of briquettes are suitable for tiled stoves, including loosely pressed ones. Softwood briquettes have around 2 percent more calorific value than hardwood briquettes.
Both information comes from sanier.de and haustechnikdialog.de. The advantage of hardwood lies not in its calorific value, but in its burning behavior. Our variety overview and the article on the best wood briquettes for heating help with the selection.
Which wood briquettes burn the longest?
That depends on density and shape. Read about Which wood briquettes burn the longest? If you want to use briquettes overnight, you will find information under Night briquettes. Check beforehand whether your oven is designed for this.
Are RUF briquettes an option?
RUF wood briquettes are a common design. How they are created is described in the RUF guide. Because of the information above, you should only use our RUF bark briquettes if your instructions expressly allow it.
Which wood briquettes burn the longest in a tiled stove?
RUF hardwood briquettes and Pini-Kay briquettes burn the longest in the tiled stove, often over three hours each with little air supply.
The burning time depends on three factors: the type of wood, the press density and the shape of the briquette. We recommend the following types for the tiled stove:
- RUF briquettes made of hardwood (beech, oak): These cuboid briquettes have a high density and develop a long-lasting glow. They are ideal for continuous burning in the tiled stove. buy RUF wood briquettes in Germany is possible from us in pallets of 960 kg.
- Pini Kay briquettes: The cylindrical shape with the characteristic hole in the middle ensures even air circulation during combustion. Pini-Kay briquettes made of hardwood achieve burning times of three to four hours and are particularly suitable for evening lighting. Buy Pini Kay briquettes Germany directly through our shop.
- Nestro briquettes: These round mixed wood briquettes are an affordable option for day-to-day operations. The burning time is around 1.5 to 2.5 hours. Nestro buys wood briquettes in Germany in large quantities upon request.
- Bark briquettes: They burn slowly and develop a mild, sustained heat over four to six hours. Ideal as night reduction in the basic furnace, but with a higher ash content of three to five percent.
“A well-fired tiled stove with high-quality wood briquettes can give off heat for up to 24 hours after heating it once without having to refill it.” (Source: German Pellet Institute, DEPI)
Comparison table: the best briquette types for tiled stoves
| Briquette Type | Type of wood | Heat value (kWh/kg) | Burning time | Ash content | Suitable for tiled stove |
|---|---|---|---|---|---|
| RUF Hardwood | Beech, Oak | 5.0 to 5.3 | 2 to 3 hours | under 1% | Yes, ideal. |
| RUF softwood | Spruce, pine | 4.8 to 5.0 | 1.5 to 2 hours | under 0.5% | Yes, good. |
| Pini Kay | Oak, Beech | 5.1 to 5.3 | 3 to 4 hours | under 1% | Yes, ideal. |
| Nestro | Mixed wood | 4.5 to 4.8 | 1.5 to 2.5 hours | 1 to 2% | Conditional |
| bark briquette | Bark | 4.0 to 4.5 | 4 to 6 hours | 3 to 5 % | As night cover |
Buy wood briquettes for tiled stoves in Germany, Austria, and Switzerland
We deliver wood briquettes in pallets and truckloads to private households and businesses throughout Central Europe. Our warehouse is located in Břežany, Czech Republic, from where we ship within a few business days to Germany, Austria, and Switzerland.
For customers in Germany, we offer buy wood briquettes in Germany with free delivery from a minimum order quantity of one ton. In Austria, you can buy buy wood briquettes in Austria and in Switzerland buy wood briquettes in Switzerland. All prices include transport and are charged based on weight.
Our tip: Order in summer when demand is lower. This way, you secure better prices and have your stock in stock in time before the heating season. Also read our article on “Buying Wood Briquettes Cheaply – Tips for Your Budget”.
How do you properly heat a tiled stove with wood briquettes?
Place two to three briquettes on an existing ember bed and set the air supply to a medium level for even heat.
Heating with briquettes differs from heating with firewood in several respects. Here are the key steps:
- Ignite: Use dry ignition aids and thin wood shavings to ignite an initial fire. First, place only one briquette on top and wait until it is fully burned.
- Add : Once a stable glow bed has formed, add two to three briquettes. Be careful not to fully open the air supply, as briquettes burn too quickly if too much oxygen is used and can overheat the combustion chamber.
- Regulate air supply: Set the supply air to a middle position. The tiled stove needs slow, even combustion so that the firebricks can absorb and store the heat.
- Night operation: For the night we recommend a bark briquette or a large RUF briquette made of hardwood. Close the air supply almost completely so that the briquette slowly smolders over several hours.
For more information on how to heat up properly, see our guide. How long do wood briquettes last?

Wood briquettes or firewood for the tiled stove: which is better?
Wood briquettes provide significantly more heat per kilogram and less ash than firewood, but require a carefully adjusted air supply in the tiled stove.
The comparison between wood briquettes and firewood depends on several factors. Here are the most important differences:
- Heat value: Briquettes reach 4.8 to 5.3 kWh/kg, while air-dry logs are around 3.5 to 4.2 kWh/kg. This means you need less fuel for the same amount of heat.
- Moisture: Briquettes have a residual moisture of less than 10 percent. Logs are often still at 15 to 20 percent even after two years of drying.
- Storage: Briquettes take up less space and can be stacked neatly. Logs require a well-ventilated storage area and at least one to two years of drying time.
- Combustion: Briquettes burn more evenly and produce less fine dust. The German Environment Agency points out that dry, pressed fuels can significantly reduce emissions from wood burning.
- Cost: Briquettes are often cheaper per kilowatt hour than oven-ready logs, especially if you order in large quantities. You can find a detailed cost comparison at wood briquettes or firewood: calorific value and price.
For the tiled stove we recommend a combination: briquettes for long-term burning and night-time heating, logs for quick heating in the morning. You can also buy dried firewood in our shop.
Order wood briquettes for tiled stoves in tons and save costs
Buying in bulk is worth it. For orders of three tons or more, we offer graduated prices that significantly reduce the price per kilo. A pallet with 960 kg wood briquettes usually contains 96 packages of 10 kg each. For an average tiled stove in a single-family home, we expect consumption of around two to four tons per heating season, depending on the size of the stove and the insulation of the building.
Further information about the pallet composition can be found at Wooden briquettes pallet 960 kg contents and delivery. For a comprehensive overview of all types of briquettes, we recommend our Wood briquettes comparison types calorific value prices.
Important storage tips
- Store briquettes dry and frost-free, preferably in a closed room or under a waterproof tarpaulin.
- Avoid direct contact with the ground. Place the pallets on squared timbers or shelves.
- Briquettes absorb moisture from the air and swell if left unprotected. This reduces the calorific value and the burning time.
- For further information, see How to store firewood correctly, the same principles also apply to briquettes.
Where can you buy and order wood briquettes for the tiled stove?
You can buy wood briquettes for tiled stoves from Wood Brezany in Germany, Austria and Switzerland, on a pallet or as a load by truck.
Buy wood briquettes in Germany
All details can be found on the page “Buying wood briquettes in Germany”. Price-conscious buyers can find tips at “Buy wood briquettes cheaply”.
Buy wood briquettes in Austria
For Austria there is the page “Buy wood briquettes in Austria”.
Buy wood briquettes in Switzerland
Swiss customers can find everything on buy wood briquettes in Switzerland.
How should you store wood briquettes?
Store wood briquettes in a dry, well-ventilated place and protected from moisture, for example in a covered storage room, in a dry cellar or in the garage.
According to sanier.de, properly stored fuel can survive longer periods of time without any loss of quality. According to this source, the ash from pure wood briquettes without binding agents can be composted. You can store logs according to our guide “Store firewood correctly”. How long a delivery lasts can be found under “How long do wood briquettes last?”.
Why order wood briquettes for tiled stoves in bulk?
If you need larger quantities, you can order wood briquettes on pallets or by truck. In terms of calorific value, they require less storage space than logs.
The statement about the storage area comes from sanier.de. If you plan an entire heating season, you can order in one step and plan the storage space in advance. You can read more about us on “About us”. How much do you need for your oven? Write to us about oven type and annual requirement.
What questions are frequently asked about wood briquettes for tiled stoves?
How long do wood briquettes burn in a tiled stove?
Depending on the type, the burning time is between 1.5 and 4 hours per briquette. RUF briquettes made from hardwood and Pini Kay briquettes achieve the longest burning times. With the air supply in the basic furnace closed, a single night briquette made of bark can glow for up to six hours. More about this under Which wood briquettes burn the longest.
What calorific value do wood briquettes have in a tiled stove?
The calorific value is between 4.5 and 5.3 kWh/kg, depending on the type of wood and the pressed density. Hardwoodbriquettes made from beech or oak achieve the highest values. For comparison: One liter of heating oil contains around 10 kWh, which means that two kilograms of wood briquettes correspond to approximately one liter of heating oil. Further details can be found at What is the calorific value of wood briquettes in comparison.
Can you use RUF briquettes in the tiled stove?
Yes, RUF briquettes are among the best fuels for the tiled stove. Their rectangular shape enables stable stratification in the combustion chamber, and the high pressure ensures slow, even combustion. Be sure to choose RUF briquettes made from hardwood if you want to achieve maximum heat retention in the firebricks. Our guide to wood briquettes and RUF briquettes provides further information.
How do you properly store wood briquettes for a tiled stove?
Store briquettes in a dry, well-ventilated area with a relative humidity below 60 percent. Avoid direct sunlight and soil moisture. A garage, basement or covered shelter works well. Briquettes that absorb moisture lose calorific value and break down more quickly when burned.
Where can you buy wood briquettes for tiled stoves online?
You can order wood briquettes for tiled stoves directly in our shop. We deliver in pallets from 960 kg and in truckloads from 24 tons to Germany, Austria and Switzerland. If you have any questions about quantities, prices or delivery times contact Wood Brezany or visit our Frequently Asked Questions page.
How long do wood briquettes burn in a tiled stove?
According to sanier.de, softwood briquettes burn for around one to two hours. According to the state of Upper Austria, the tiled stove is only refilled after 8 to 10 hours.
The burning time depends on the type and compression as well as the heat release of the storage mass.
Can you burn bark briquettes in a tiled stove?
The Bavarian State Office for the Environment excludes bark briquettes for fireplaces. For tiled stoves, the operating instructions decide. I cannot confirm a blanket statement.
Can you add more wood briquettes?
The HKI states that adding wood briquettes to an existing bed of embers is common practice. Your instructions will determine whether you mix briquettes with firewood.
How dry do wood briquettes have to be?
The 1st BImSchV requires humidity below 25 percent. The data sheet of a commercial product states less than 5.8 percent residual moisture, your batch may vary.
How many briquettes replace one cubic meter of wood?
According to the manufacturer’s data sheet, 1,000 kg of wood briquettes replace around 3 cubic meters of mixed wood. This is a manufacturer’s specification that changes your stove and the type of wood you use.
You can find further answers in our frequent questions.
Sources
- 1. BImSchV § 3 Fuels, laws on the Internet
- Federal Environment Agency, New regulations of the 1st BImSchV
- LANUV NRW, heating with wood
- Bavarian State Office for the Environment, operating fireplaces in an environmentally friendly manner
- sanier.de, heating with briquettes
- HKI, Heating correctly with wood
- State of Upper Austria, really heat up
